My next FPV racing machine...

-
Here are some renderings of my latest frame concept. It has a very small frontal area and should reach high speeds. The diagonal motor distance is 210 mm and I will use 5.5 inch propellers (Graupner Race-Prop or C-prop).
















Comments

  1. TheSFReader1 February 2016 at 14:52

    Hi, I follow youy test, and wonder if adding some "tail" in addition to the nose would help aerodinamically, compensating its weight with better performance ?

    ReplyDelete
  2. Stefan4 February 2016 at 23:23

    Mal wieder ein sehr cooles Design!

    Ich habe eine Frage zur MM6: Hattest du eigentlich Probleme mit Vibrationen etc.? Da die Props ja doch sehr nah beieinander sind.
    Ich überlege nämlich schon seit 5 Jahren die mal nachzubauen ;)

    Gruß Stefan

    ReplyDelete
    Replies
    1. William Thielicke5 February 2016 at 11:28

      Hallo Stefan,
      Nein vibrationsprobleme hatte ich keine. Die Propeller drehen ja an den Blattspitzen in die gleiche Richtung, da sollte ein kleiner Abstand keine Probleme machen.

      Delete
    2. Stefan5 February 2016 at 12:18

      Okay, Danke.
      Ich hatte nämlich bei einem größeren Quad das Problem, aber der hatte auch 10" Props.
      Dann werde ich mal das zeichnen und bauen anfangen. Ich schicke dir Bilder wenn ich fertig bin. :)

      Delete
    3. Stefan5 February 2016 at 23:09

      This comment has been removed by the author.

      Delete
  3. Unknown27 February 2016 at 09:16

    This comment has been removed by the author.

    ReplyDelete
  4. Unknown27 February 2016 at 09:46

    Cool design! I would like too such to make.
    With what thickness of a layer the case is printed? Or it is not the FDM print?
    Whether you will share STL files of the case?

    ReplyDelete
  5. Anonymous6 March 2016 at 21:21

    This will fly like awesomeness! Share the CAD files and save me the trouble of drawing it myself please? :)

    ReplyDelete
  6. Anonymous6 March 2016 at 21:53

    Oh found them, thanks!

    ReplyDelete

Post a Comment

Popular posts from this blog

My 15 inch long-range setup for 2020 (with CAD files)

-
Image
This is my latest 15 inch ultra-long range setup with 50 minutes flight time: Propellers: 15x5.5" Tarot with custom hub  Motors: T-Motor MN3110 470 kV  Frame: 240g custom carbon structure  Lipo: 2x 4S 4000 mAh SLS 20C (parallel)  Camera: Micro Runcam micro sparrow  Firmware: INAV  FC: Holybro Kakute F7  ESC: Tekko32 F3  GPS: BN-180  Compass: QMC5883L  Receiver: FRSky R9 slim+  Hovering flight time is 50 minutes at 8.5 Amps and 40% throttle. Current goes up to 12 A when flying 50-60 km/h. Flight characteristics are really good when tuned properly (you'll nee a HUGE D-term). Here is the CAD file of the frame. INAV 2.4.0 PID settings:  set mc_p_pitch = 85 set mc_i_pitch = 60 set mc_d_pitch = 150 set mc_p_roll = 85 set mc_i_roll = 60 set mc_d_roll = 150 set mc_p_yaw = 200 set mc_i_yaw = 70 set mc_p_level = 40 set mc_i_level = 10 set max_angle_inclination_rll = 500 set max_angle_inclination_pit = 500 set dterm_...
Read more

Finished I²C to PWM converter and TriGUIDE mini

-
Image
The last nights were a bit shorter for me, since the PCBs I ordered at bilex-lp.com arrived. They look really good and seem to be of high quality (I ordered a different "solder resist" colour, well, I like bright colors, but anyway... ). So I had the opportunity to do my very first SMD solderings. This really seems to be comfortable... I will completely switch to SMD I think. The I²C to PWM converters work! Here are the features: Weight under 1 g Works with (most likely many) standard ESCs (currently tested: HK SS 18-20A, ...) I²C address selectable via solder jumpers (4 standard mikrokopter addresses dec 82, 84, 86, 88) Refresh rate selectable via solder jumpers (417 Hz, 292 Hz, 155 Hz, 49 Hz) Pulse width (I²C 0-255): 990µS - 2010µS Pulse width at startup (3 s): 920µS Motor off when no I²C connection longer than 256ms Motor off when microcontroller crashes (veeeery unlikely) Powered by the BEC of the ESC, or by an external 5V source (prepared as well) Very eas...
Read more

Aerodynamics in racing multirotors!

-
Image
Why future racing copters really should look different. by Dr. William Thielicke aka Willa aka Shrediquette ABSTRACT In this article I try to demonstrate why FPV racing multirotors need to look different. Some small modifications to the frame would (in theory…!) result in 70 % higher top speed! All that needs to be done is to align the arms parallel to the propeller flow, and to tilt the main body of the copter by about 40 degrees. I am presenting a very simple and robust racing copter design that incorporates these ideas. Furthermore, I am calculating the aerodynamic drag of different copter concepts using basic equations. The aim of this article is to make you realize the importance of aerodynamics and to stimulate people to design more innovative racing frames. INTRODUCTION Until recently, multirotors were mainly used as a “hovering device” and the top speed of these copters did hardly matter. Now, multirotor racing has become popular and all competitors are seeking ...
Read more

More propeller tests

-
Image
Recently, I discovered some small counter-rotating propellers that I didn't know before. I ordered some and did some tests. The red 4x4.5" props look really good, nice thin airfoils and a good precision. During the tests, they made the least amount of noise, and are currently my preferred ones. The performance of the 4x2.5" props is even better, but they have a pretty terrible sound and seem to be less balanced. Both propellers outperform the AirAce propellers, but this is not really a surprise because the AirAce have a smaller diameter and more blades. What is also interesting is the weight of the propellers. A propeller with a lower weight potentially has a lower moment of inertia which is beneficial for the control loops: AirAce: 2.1 g 4x2.5": 1.5 g 4x4.5" : 1.3 g So this is an advantage for the 4x4.5" propellers, especially because the weight of this propeller is more concentrated to the center, which should further lower the momentof inertia. ...
Read more

Part 1/3: Side Force Generators (SFGs) in FPV Racing

-
Image
Summary: FPV racing multirotors with side force generators (SFGs), will drift less during turns, making them potentially faster on race tracks  (watch the video comparison here ) . But the SFGs need the be carefully placed and dimensioned, so that aerodynamic centre and centre of mass are at the same position. Otherwise it will not work.  Introduction Recently, I was thinking about how to improve the handling of racing copters. I noticed since quite a long time, that different copters behave quite differently in fast turns: Some drift quite a lot (especially when they carry a larger battery or an action cam), others drift less. I was always preferring copters that drift as little as  possible. That is also why I am trying to reduce the weight of my copters as much as feasible. The amount of drift depends on the weight of the copter and the lift and drag of the fuselage for sideways air streams (side-slip). The larger the lift and drag, the more side force the fusel...
Read more