-
Next Steps...: I will also post the circuit layout, the source code of the copter and everything else on this webpage soon.

Comments

  1. Unknown12 September 2009 at 13:40

    Much appreciated! Been following your progress, well done!

    ReplyDelete

Post a Comment

Popular posts from this blog

Some thoughts on FPV camera tilt compensation

-
Almost every 'serious' FPV racer is tilting the FPV camera up in order to have a better image during fast flight. Angles between 10 and 35 degrees seem to be common. E.g. I am using 25 degrees. But tilting the camera with respect to the multirotors horizontal plane has a side effect on the controls (maybe you never thought about it, because you are so used to flying with this side effect). Just to make the effect easier to visualize: Imagine you drank a beer too much and now you suddenly think you are Charpu , Mr Steele or Mattystuntz . You mount your FPV camera with 90 degrees tilt (pointing up vertically) because your best friend told you that all the pros do it like this. In this case, your roll and yaw control will be interchanged: When you move your RC sticks to roll left, your copter will roll left, but looking through the FPV camera, it appears as if you are yawing to the left! And if you move your RC sticks to yaw left, your copter will of course yaw left, but the im...
Read more

Finished I²C to PWM converter and TriGUIDE mini

-
Image
The last nights were a bit shorter for me, since the PCBs I ordered at bilex-lp.com arrived. They look really good and seem to be of high quality (I ordered a different "solder resist" colour, well, I like bright colors, but anyway... ). So I had the opportunity to do my very first SMD solderings. This really seems to be comfortable... I will completely switch to SMD I think. The I²C to PWM converters work! Here are the features: Weight under 1 g Works with (most likely many) standard ESCs (currently tested: HK SS 18-20A, ...) I²C address selectable via solder jumpers (4 standard mikrokopter addresses dec 82, 84, 86, 88) Refresh rate selectable via solder jumpers (417 Hz, 292 Hz, 155 Hz, 49 Hz) Pulse width (I²C 0-255): 990µS - 2010µS Pulse width at startup (3 s): 920µS Motor off when no I²C connection longer than 256ms Motor off when microcontroller crashes (veeeery unlikely) Powered by the BEC of the ESC, or by an external 5V source (prepared as well) Very eas...
Read more

Aerodynamics in racing multirotors!

-
Image
Why future racing copters really should look different. by Dr. William Thielicke aka Willa aka Shrediquette ABSTRACT In this article I try to demonstrate why FPV racing multirotors need to look different. Some small modifications to the frame would (in theory…!) result in 70 % higher top speed! All that needs to be done is to align the arms parallel to the propeller flow, and to tilt the main body of the copter by about 40 degrees. I am presenting a very simple and robust racing copter design that incorporates these ideas. Furthermore, I am calculating the aerodynamic drag of different copter concepts using basic equations. The aim of this article is to make you realize the importance of aerodynamics and to stimulate people to design more innovative racing frames. INTRODUCTION Until recently, multirotors were mainly used as a “hovering device” and the top speed of these copters did hardly matter. Now, multirotor racing has become popular and all competitors are seeking ...
Read more

My 15 inch long-range setup for 2020 (with CAD files)

-
Image
This is my latest 15 inch ultra-long range setup with 50 minutes flight time: Propellers: 15x5.5" Tarot with custom hub  Motors: T-Motor MN3110 470 kV  Frame: 240g custom carbon structure  Lipo: 2x 4S 4000 mAh SLS 20C (parallel)  Camera: Micro Runcam micro sparrow  Firmware: INAV  FC: Holybro Kakute F7  ESC: Tekko32 F3  GPS: BN-180  Compass: QMC5883L  Receiver: FRSky R9 slim+  Hovering flight time is 50 minutes at 8.5 Amps and 40% throttle. Current goes up to 12 A when flying 50-60 km/h. Flight characteristics are really good when tuned properly (you'll nee a HUGE D-term). Here is the CAD file of the frame. INAV 2.4.0 PID settings:  set mc_p_pitch = 85 set mc_i_pitch = 60 set mc_d_pitch = 150 set mc_p_roll = 85 set mc_i_roll = 60 set mc_d_roll = 150 set mc_p_yaw = 200 set mc_i_yaw = 70 set mc_p_level = 40 set mc_i_level = 10 set max_angle_inclination_rll = 500 set max_angle_inclination_pit = 500 set dterm_...
Read more

First successful GPS position hold tests!

-
Image
I added a GPS module, a compass and a pressure sensor to my tricopter to enable automatic position hold. GPS is implemented using a PD control loop, compass is P only, and height is PID. And... it works! Still not optimal, but in principle it is already ok. There are some things that have to be optimized of course, e.g. a one-axis compass will probably not work for waypoint navigation and position hold when there is wind. And my code is still far from being optimal. At the moment, I have to make my copter hover at the position + height that I want. Then, I flip a switch (connected to channel 6) - current position, heading and height is stored and used as setpoint for position hold. I think I will have to switch to a 3-axes compass in combination with an additional 3-axes accelerometer. That will enable tilt compensation for the compass, as well as improving the D-term for height stabilization. The tests that you see in the video where done with no wind at all. The tricopter stayed mo...
Read more